API 5CT Casing Steel Pipes API K55 CASING Oil Well Drilling Oil Tubular Goods Oil And Gas Pipeline Large-Diameter Pipe Tube

Description

 API 5ct K55 Casing tubing is a API 5CT Oil casing Pipe & mainly used for oil well drilling. it is available as short thread type and long thread type supplied with their couplings.

API 5CT k55 casing Tubing serves to transport both crude oil and natural gas from Oil and Gas layer to the surface pipeline after drilling is completed. It is able to bear the pressure produced by the exploitation process. After the outer surface is coated with a protective layer, the tubing is marked in accordance with the API 5CT standard and strapped with metal belt.

The K55 API-5CT casing pipe is a comparatively low steel grade in oil drilling. It is widely applied for shallow oil and gas extraction.Because of  its low cost among other grades of steel, it enjoys wider applications,  can be generally used in shallow wells, geothermal wells, and water wells.

K55 Casing is placed downhole to provide structural integrity to the wellbore and must withstand external-collapse pressure from rock formations and internal-yield pressure from fluid and gas. It must also hold its own deadweight and withstand the torque and transaxial pressure placed on it while running downhole

according to american petroleum institute Standard api spec 5ct, the steel grade of API 5CT oil casing pipe can be divided into ten types, including H-40, J-55, K-55, N-80, C-75, L-80, C-90, C-95, p-110 and Q-125. We supply the casing pipe & api 5ct J55 Casing Tubing accompanied with thread and coupling, or we offer our product in accordance with the following forms for option.

K55 api casing or tubing is a relatively common one in oil drilling. Because of the low steel grade of K55, it is used for shallow oil and gas extraction. Due to its low Price among other grades of steel, it enjoys broader applications. The J55 API casing or tubing is widely used in the extraction of natural gas and coalbed methane, and can be commonly found in shallow wells, geothermal wells, and water wells.

API 5CT K55 Casing Tubing Type of Casing：

• short round thread casing(SC)
• long round thread casing(LC)
• buttress thread casing(BC)

API 5CT K55 Casing Tubing chemical Composition:

Chemical Composition, Mass Fraction (%)
Grade		C		Mn		Mo		Cr		Ni	Cu	P	S	Si
	Type	min	max	min	max	min	max	min	max	max	max	max	max	max
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15
H40	—	—	—	—	—	—	—	—	—	—	—	—	0.03	—
J55	—	—	—	—	—	—	—	—	—	—	—	—	0.03	—
K55	—	—	—	—	—	—	—	—	—	—	—	—	0.03	—
N80	1	—	—	—	—	—	—	—	—	—	—	0.03	0.03	—
N80	Q	—	—	—	—	—	—	—	—	—	—	0.03	0.03	—
R95	—	—	0.45 c	—	1.9	—	—	—	—	—	—	0.03	0.03	0.45
L80	1	—	0.43 a	—	1.9	—	—	—	—	0.25	0.35	0.03	0.03	0.45
L80	9Cr	—	0.15	0.3	0.6	0.9	1.1	8	10	0.5	0.25	0.02	0.03	1
L80	13Cr	0.15	0.22	0.25	1	—	—	12	14	0.5	0.25	0.02	0.03	1
C90	1	—	0.35	—	1.2	0.25 b	0.85	—	1.5	0.99	—	0.02	0.03	—
T95	1	—	0.35	—	1.2	0.25 b	0.85	0.4	1.5	0.99	—	0.02	0.03	—
C110	—	—	0.35	—	1.2	0.25	1	0.4	1.5	0.99	—	0.02	0.03	—
P110	e	—	—	—	—	—	—	—	—	—	—	0.030 e	0.030 e	—
Q125	1	—	0.35		1.35	—	0.85	—	1.5	0.99	—	0.02	0.01	—
NOTE elements shown shall be reported in product analysis.
a The carbon content for L80 may be increased up to 0.50 % maximum if the product is oil-quenched or polymer-quenched.
b The molybdenum content for Grade C90 Type 1 has no minimum tolerance if the wall thickness is less than 17.78 mm.
c The carbon content for R95 may be increased up to 0.55 % maximum if the product is oil-quenched.
d The molybdenum content for T95 Type 1 may be decreased to 0.15 % minimum if the wall thickness is less than 17.78 mm.
e For EW Grade p110, the phosphorus content shall be 0.020 % maximum and the sulfur content 0.010 % maximum.

API 5CT K55 Casing Tubing mechanical properties:

Tensile and Hardness requirements
Grade			Yield strength MPa		Tensile Strength	Hardness a,c		Specified Wall Thickness	Allowable Hardness Variation b
	Type	Total Elongation Under Load			min MPa	max
			min	max		HRC	HBW	mm	HRC
1	2	3	4	5	6	7	8	9	10
H40	—	0.5	276	552	414	—	—	—	—
J55	—	0.5	379	552	517	—	—	—	—
K55	—	0.5	379	552	655	—	—	—	—
N80	1	0.5	552	758	689	—	—	—	—
N80	Q	0.5	552	758	689	—	—	—	—
R95	—	0.5	655	758	724	—	—	—	—
L80 L80	1	0.5	552	655	655	23	241	—	—
L80	9Cr 13Cr	0.5	552	655	655	23	241	—	—
		0.5	552	655	655	23	241	—	—
C90	1	0.5	621	724	689	25.4	255	£12.70	3
								12.71 to 19.04	4
								19.05 to 25.39	5
								³ 25.40	6
T95	1	0.5	655	758	724	25.4	255	£12.70	3
								12.71 to 19.04	4
								19.05 to 25.39	5
								³ 25.40	6
C110	—	0.7	758	828	793	30	286	£12.70	3
								12.71 to 19.04	4
								19.05 to 25.39	5
								³ 25.40	6
P110	—	0.6	758	965	862	—	—	—	—
Q125	1	0.65	862	1034	931	b	—	£12.70	3
								12.71 to 19.04 19.05	4
									5
a In case of dispute, laboratory Rockwell C hardness testing shall be used as the referee method.
b No hardness limits are specified, but the maximum variation is restricted as a manufacturing control in accordance with 7.8 and 7.9.
c For through-wall hardness tests of Grades L80 (all types), C90, T95 and C110, the requirements stated in HRC scale are for maximum mean hardness number.

 

API 5CT K55 Casing Tubing range lengths
	Range 1	Range 2	Range 3
CASING (PE/T and C/SF)
Total range length, inclusive Permissible variation, max a	4.88 to 7.62 1.83	7.62 to 10.36	10.36 to 14.63 1.83
		1.52
TUBING AND CASING USED AS TUBING
(PE/T and C/SF)
Total range length, inclusive Permissible variation, max a	6.10 to 7.32 b	8.53 to 9.75 c	11.58 to 12.80 d
	0.61	0.61	0.61
INTEGRAL TUBING connectionS (including IJ/PE
and IJ/SF)
Total range length, inclusive Permissible variation, max a	6.10 to 7.92 e	8.53 to 10.36	11.58 to 13.72 0.61
	0.61	0.61
pup jointS	Lengths: 0.61; 0.91; 1.22; 1.83; 2.44; 3.05 and 3.66 e
	Tolerance: ±0.076
a Length variation applies to rail car shipment to the point of use and does not apply to order items of less than 18,144 kg of pipe.
b By agreement between purchaser and manufacturer, the maximum length may be increased to 8.57 m.
c By agreement between purchaser and manufacturer, the maximum length may be increased to 10.76 m.
d By agreement between purchaser and manufacturer, the maximum length may be increased to 17.72 m.0.61 m pup joints may be furnished up to 0.91 m long by agreement between purchaser and manufacturer, and lengths other than those listed may be furnished by agreement between purchaser and manufacturer.

 API 5CT K55 Casing Tubing applicable end-finish

Casing List (sizes, masses, wall thickness, grade, and applicable end-finish)

Labels		Outside diameter (d/mm)	T&C (kg/m)	Wall thickness   (t/mm)	Type of end-finish
1	2				J55/K55	M65	L80/R95	N80-1/Q	C90/T95	P110	Q125
4-1/2	9.50	114.30	14.14	5.21	PS	PS	–	–	–	–	–
	10.50	114.30	15.63	5.69	PSB	PSB	–	–	–	–	–
	11.60	114.30	17.26	6.35	PSLB	PLB	PLB	PLB	PLB	PLB	–
	13.50	114.30	20.09	7.37	–	PLB	PLB	PLB	PLB	PLB	–
	15.10	114.30	22.47	8.56	–	–	–	–	–	PLB	PLB
5	11.50	127.00	17.11	5.59	PS	PS	–	–	–	–	–
	13.00	127.00	19.35	6.43	PSLB	PSLB	–	–	–	–	–
	15.00	127.00	22.32	7.52	PSLB	PLB	SLB	PLB	PLB	PLB
	18.00	127.00	26.79	9.19	–	PLB	SLB	PLB	PLB	PLB	PLB
	21.40	127.00	31.85	11.10	–	PLB	PLB	PLB	PLB	PLB	PLB
	23.20	127.00	34.53	12.14	–	–	PLB	PLB	PLB	PLB	PLB
	24.10	127.00	35.87	12.70	–	–	PLB	PLB	PLB	PLB	PLB
5-1/2	14.00	139.70	20.83	6.20	PS	PS	–	–	–	–	–
	15.50	139.70	23.07	6.98	PSLB	PSLB	–	–	–	–	–
	17.00	139.70	25.30	7.72	PSLB	PLB	PLB	PLB	PLB	PLB	–
	20.00	139.70	29.76	9.17	–	PLB	PLB	PLB	PLB	PLB	–
	23.00	139.70	34.23	10.54	–	PLB	PLB	PLB	PLB	PLB	PLB
	26.80	139.70	39.88	12.70	–	–	–	–	P	–	–
	29.70	139.70	44.20	14.27	–	–	–	–	P	–	–
	32.60	139.70	48.52	15.88	–	–	–	–	P	–	–
	35.30	139.70	52.53	17.45	–	–	–	–	P	–	–
	38.00	139.70	56.55	19.05	–	–	–	–	P	–	–
	40.50	139.70	60.27	20.62	–	–	–	–	P	–	–
	43.10	139.70	64.14	22.22	–	–	–	–	P	–	–
6-5/8	20.00	168.28	29.76	7.32	PSLB	PSLB	–	–	–	–	–
	24.00	168.28	35.72	8.94	PSLB	PLB	PLB	PLB	PLB	PLB	–
	28.00	168.28	41.67	10.59	–	PLB	PLB	PLB	PLB	PLB	–
	32.00	168.28	47.62	12.06	–	–	PLB	PLB	PLB	PLB	PLB
7	17.00	177.80	25.30	5.87	–	–	–	–	–	–	–
	20.00	177.80	29.76	6.91	PS	PS	–	–	–	–	–
	23.00	177.80	34.23	8.05	PSLB	PLB	PLB	PLB	PLB	–	–
	26.00	177.80	38.69	9.19	–	PLB	PLB	PLB	PLB	PLB	–
	29.00	177.80	43.16	10.36	–	PLB	PLB	PLB	PLB	PLB	–
	32.00	177.80	47.62	11.51	–	PLB	PLB	PLB	PLB	PLB	–
	35.00	177.80	52.09	12.65	–	–	PLB	PLB	PLB	PLB	PLB
	38.00	177.80	56.55	13.72	–	–	PLB	PLB	PLB	PLB	PLB
	42.70	177.80	63.55	15.88	–	–	–	–	P	–	–
	46.40	177.80	69.05	17.45	–	–	–	–	P	–	–
	50.10	177.80	74.56	19.05	–	–	–	–	P	–	–
	53.60	177.80	79.77	20.62	–	–	–	–	P	–	–
	57.10	177.80	84.98	22.22	–	–	–	–	P	–	–
7-5/8	24.00	193.68	35.72	7.62	–	–	–	–		–	–
	26.40	193.68	39.29	8.33	PSLB	PSLB	PLB	PLB	PLB	–	–
	29.70	193.68	44.20	9.52	–	PLB	PLB	PLB	PLB	PLB	–
	33.70	193.68	50.15	10.92	–	PLB	PLB	PLB	PLB	PLB	–
	39.00	193.68	58.04	12.70	–	–	PLB	PLB	PLB	PLB	PLB
	42.80	193.68	63.69	14.27	–	–	PLB	PLB	PLB	PLB	PLB
	45.30	193.68	67.42	15.11	–	–	PLB	PLB	PLB	PLB	PLB
	47.10	193.68	70.09	15.88	–	–	PLB	PLB	PLB	PLB	PLB
	51.20	193.68	76.20	17.45	–	–	–	–	P	–	–
	55.30	193.68	82.30	19.05	–	–	–	–	P	–	–
7-3/4	46.10	196.85	68.61	15.11	–	–	P	P	P	P	P
8-5/8	24.00	219.08	35.72	6.71	PS	PS	–	–	–	–	–
	28.00	219.08	41.67	7.72		PS	–	–	–	–	–
	32.00	219.08	47.62	8.94	PSLB	PSLB	–	–	–	–	–
	36.00	219.08	53.58	10.16	PSLB	PSLB	PLB	PLB	PLB	PLB	–
	40.00	219.08	59.53	11.43	–	PLB	PLB	PLB	PLB	PLB	–
	44.00	219.08	65.48	12.70	–	–	PLB	PLB	PLB	PLB	–
	49.00	219.08	72.92	14.15	–	–	PLB	PLB	PLB	PLB	PLB
9-5/8	32.30	244.48	48.07	7.92	–	–	–	–	–	–	–
	36.00	244.48	53.58	8.94	PSLB	PSLB	–	–	–	–	–
	40.00	244.48	59.53	10.03	PSLB	PSLB	PLB	PLB	PLB	–	–
	43.50	244.48	64.74	11.05	–	PLB	PLB	PLB	PLB	PLB	–
	47.00	244.48	69.95	11.99	–	PLB	PLB	PLB	PLB	PLB	PLB
	53.50	244.48	79.62	13.84	–	–	PLB	PLB	PLB	PLB	PLB
	58.40	244.48	86.91	15.11	–	–	PLB	PLB	PLB	PLB	PLB
	59.40	244.48	88.40	15.47	–	–	–	–	P	–	–
	64.90	244.48	96.58	17.07	–	–	–	–	P	–	–
	70.30	244.48	104.62	18.64	–	–	–	–	P	–	–
	75.60	244.48	112.51	20.24	–	–	–	–	P	–	–
10-3/4	32.75	273.05	48.74	7.09	–	–	–	–	–	–	–
	40.50	273.05	60.27	8.89	PSB	PSB	–	–	–	–	–
	45.50	273.05	67.71	10.16	PSB	PSB	–	–	–	–	–
	51.00	273.05	75.90	11.43	PSB	PSB	PSB	PSB	PSB	PSB	–
	55.50	273.05	82.60	12.57	–	PSB	PSB	PSB	PSB	PSB	–
	60.70	273.05	90.33	13.84	–	–	–	–	PSB	PSB	PSB
	65.70	273.05	97.77	15.11	–	–	–	–	PSB	PSB	PSB
	73.20	273.05	108.94	17.07	–	–	–	–	P	–	–
	79.20	273.05	117.87	18.64	–	–	–	–	P	–	–
	85.30	273.05	126.94	20.24	–	–	–	–	P	–	–
11-3/4	42.00	298.45	62.50	8.46	–	–	–	–	–	–	–
	47.00	298.45	69.95	9.53	PSB	PSB	–	–	–	–	–
	54.00	298.45	80.36	11.05	PSB	PSB	–	–	–	–	–
	60.00	298.45	89.29	12.42	PSB	PSB	PSB	PSB	PSB	PSB	PSB
	65.00	298.45	96.73	13.56	–	–	P	P	P	P	P
	71.00	298.45	105.66	14.78	–	–	P	P	P	P	P
13-3/8	48.00	339.72	71.43	8.38	–	–	–	–	–	–	–
	54.50	339.72	81.11	9.65	PSB	PSB	–	–	–	–	–
	61.00	339.72	90.78	10.92	PSB	PSB	–	–	–	–	–
	68.00	339.72	101.20	12.19	PSB	PSB	PSB	PSB	PSB	PSB	–
	72.00	339.72	107.15	13.06	–	–	PSB	PSB	PSB	PSB	PSB
16	65.00	406.40	96.73	9.53	–	–	–	–	–	–	–
	75.00	406.40	111.62	11.13	PSB	PSB	–	–	–	–	–
	84.00	406.40	125.01	12.57	PSB	PSB	–	–	–	–	–
	109.00	406.40	162.21	16.66	P	–	P	P	–	P	P
18-5/8	87.50	473.08	130.22	11.05	PSB	PSB	–	–	–	–	–
20	94.00	508.00	139.89	11.13	PSLB	PSLB	–	–	–	–	–
	106.50	508.00	158.49	12.70	PSLB	PSLB	–	–	–	–	–
	133.00	508.00	197.93	16.13	PSLB	–	–	–	–	–	–

* P – plain end, S – short round thread, B – buttress, L – long round thread.

API 5CT K55 Casing Tubing Grade Color Codes
Grade	Grade Type	Number and Color of Bands for Product a with Length ³ 1.8 m	Color(s) for Couplings
			Entire Coupling	Band(s) b, c
1	2	3	4	5
H40	—	None or black band at the manufacturer’s option	None	Same as for pipe
J55 Tubing	—	One bright green	Bright green	None
J55 Casing	—	One bright green	Bright green	One white
K55	—	Two bright green	Bright green	None
N80	1	One red	Red	None
N80	Q	One red, one bright green	Red	Green
R95	—	One brown	Brown	None
L80	1	One red, one brown	Red	One brown
L80	9Cr	One red, one brown, two yellow	None	Two yellow
L80	13Cr	One red, one brown, one yellow	None	One yellow
C90	1	One purple	Purple	None
T95	1	One silver	Silver	None
C110	—	One white, two brown	White	Two brown
P110	—	One white	White	None
Q125	1	One orange	Orange	None
a In the case of coupling material, unless otherwise specified in the purchase agreement, the manufacturer’s internal requirements shall govern.
b special clearance couplings shall also have a black band.
c Seal-ring couplings shall also have a blue band.

 

API 5CT K55 Casing Tubing dimensions and Masses for Standard Casing and for Casing Threaded with
API Round Thread and Buttress Thread
Labels a							Calculated Mass c
			Nominal Linear Mass T& C b,c	Wall Thick- ness				em, Mass Gain or Loss Due to End Finishing d
		Outside Diameter			Inside Diameter	Drift Diameter	Plain- end	kg
								Round Thread		Buttress Thread
							wpe
		D	kg/m	t	D	mm	kg/m	Short	Long	RC	SCC
		mm		mm	mm
1	2	3	4	5	6	7	8	9	10	11	12
4 1/2	9.5	114.3	14.38	5.21	103.88	100.7	14.02	3.64	—	— 4.53	— 1.12
4 1/2	10.5	114.3	15.73	5.69	102.92	99.74	15.24	3.33	— 3.61	4.32	0.91
4 1/2	11.6	114.3	17.38	6.35	101.6	98.42	16.91	3.18	3.35	4.07	0.6
4 1/2	13.5	114.3	19.87	7.37	99.56	96.38	19.44	—	3.53	3.64	0.24
4 1/2	15.1	114.3	22.69	8.56	97.18	94	22.32	—
5	11.5	127	17.19	5.59	115.82	112.64	16.74	4.32	— 4.85	— 5.38	— 1.24
5	13	127	19.69	6.43	114.14	110.96	19.12	4	4.51	4.99	0.61
5	15	127	22.69	7.52	111.96	108.78	22.16	3.71	4.52	4.4	0.22
5	18	127	27.19	9.19	108.62	105.44	26.7	—	3.45	3.76	–0.62
5	21.4	127	32.13	11.1	104.8	101.62	31.73	—	3.15	3.42	–0.96
5	23.2	127	34.76	12.14	102.72	99.54	34.39	—	2.99	3.23	–1.14
5	24.1	127	36.15	12.7	101.6	98.42	35.8	—
5 1/2	14	139.7	20.91	6.2	127.3	124.12	20.41	4.6	— 5.26	— 5.71	— 0.87
5 1/2	15.5	139.7	23.48	6.98	125.74	122.56	22.85	4.36	5.31	5.41	0.58
5 1/2	17	139.7	25.72	7.72	124.26	121.08	25.13	4.14	4.5	4.84	0.45
5 1/2	20	139.7	30.05	9.17	121.36	118.18	29.52	—	4.37	4.31	-0.52
5 1/2	23	139.7	34.05	10.54	118.62	115.44	33.57	—	—	—	—
5 1/2	26.8	139.7	40.15	12.7	114.3	111.12	39.78	—	—	—	—
5 1/2	29.7	139.7	44.47	14.27	111.16	107.98	44.14	—	—	—	—
5 1/2	32.6	139.7	48.74	15.88	107.94	104.76	48.49	—	—	—	—
5 1/2	35.3	139.7	52.8	17.45	104.8	101.62	52.61	—	—	—	—
5 1/2	38	139.7	56.82	19.05	101.6	98.42	56.68	—	—	—	—
5 1/2	40.5	139.7	60.64	20.62	98.46	95.28	60.55	—	—	—	—
5 1/2	43.1	139.7	64.41	22.22	95.26	92.08	64.38	—
6 5/8	20	168.28	29.76	7.32	153.64	150.46	29.06	5.58	6.23	6.35	0.89
6 5/8	24	168.28	35.72	8.94	150.4	147.22	35.13	4.42	5.48	5.52	0.68
6 5/8	28	168.28	41.67	10.59	147.1	143.92	41.18	—	4.73	4.71	–0.75
6 5/8	32	168.28	47.62	12.06	144.16	140.98	46.46	—	4.73	4	–1.46
							Calculated Mass c
			Nominal Linear Mass T& C b,c	Wall Thick- ness				em, Mass Gain or Loss Due to End Finishing d
Labels a		Outside Diameter			Inside Diameter	Drift Diameter	Plain- end	kg
								Round Thread		Buttress Thread
							wpe
		D	kg/m	t	D	mm	kg/m	Short	Long	RC	SCC
		mm		mm	mm
1	2	3	4	5	6	7	8	9	10	11	12
7	17	177.8	25.6	5.87	166.06	162.88	24.89	7.61	—	—	—
7	20	177.8	29.91	6.91	163.98	160.8	29.12	6.74	— 7.94	— 8.28	— 0.58
7	23	177.8	34.67	8.05	161.7	158.75 e 158.52 156.24 153.90	33.7	6.26	7.94	8.28	0.58
7	23	177.8	34.67	8.05	161.7	152.40 e	33.7	6.26	7.37	7.65	–0.54
7	26	177.8	39.14	9.19	159.42	151.6	38.21	5.79	6.79	7.13	–0.69
7	29	177.8	43.6	10.36	157.08	149.32	42.78	—	6.23	6.4	–1.31
7	32	177.8	47.92	11.51	154.78	147.18	47.2	—	6.23	6.4	–1.31
7	32	177.8	47.92	11.51	154.78	142.86	47.2	—	5.68	5.79	–1.91
7	35	177.8	52.09	12.65	152.5	139.72	51.52	—	5.18	5.24	–2.47
7	38	177.8	56.1	13.72	150.36	136.52	55.52	—	—	—	—
7	42.7	177.8	63.84	15.88	146.04	133.38	63.41	—	—	—	—
7	46.4	177.8	69.35	17.45	142.9	130.18	69.01	—	—	—	—
7	50.1	177.8	74.85	19.05	139.7		74.58	—	—	—	—
7	53.6	177.8	80.21	20.62	136.56		79.93	—	—	—	—
7	57.1	177.8	85.42	22.22	133.36		85.25	—
7 5/8	24	193.68	35.72	7.62	178.44	175.26	34.96	7.11	— 8.58	— 9.12	— 2.59
7 5/8	26.4	193.68	39.29	8.33	177.02	173.84	38.08	6.78	7.91	8.38	1.84
7 5/8	29.7	193.68	44.2	9.52	174.64	171.46	43.24	—	7.13	7.51	0.98
7 5/8	33.7	193.68	50.15	10.92	171.84	168.66	49.22	—	6.16	6.44	– 0.10
7 5/8	39	193.68	58.04	12.7	168.28	165.1	56.68	—	5.32	5.5	–1.03
7 5/8	42.8	193.68	63.69	14.27	165.14	161.96	63.14	—	4.87	5.01	–1.52
7 5/8	45.3	193.68	67.41	15.11	163.46	160.28	66.54	—	4.48	4.57	–1.96
7 5/8	47.1	193.68	70.09	15.88	161.92	158.74	69.63	—	—	—	—
7 5/8	51.2	193.68	76.19	17.45	158.78	155.6	75.84	—	—	—	—
7 5/8	55.3	193.68	82.3	19.05	155.58	152.4	82.04	—
7 3/4	46.1	196.85	68.6	15.11	166.63	165.10 e	67.72	—	—	—	—
7 3/4	46.1	196.85	68.6	15.11	166.63	163.45	67.72	—	—	—	—
Labels a							Calculated Mass c
			Nominal Linear Mass T& C b,c	Wall Thick- ness				em, Mass Gain or Loss Due to End Finishing d
		Outside Diameter			Inside Diameter	Drift Diameter	Plain- end	kg
								Round Thread		Buttress Thread
							wpe
		D	kg/m	t	D	mm	kg/m	Short	Long	RC	SCC
		mm		mm	mm
1	2	3	4	5	6	7	8	9	10	11	12
8 5/8	24	219.08	35.72	6.71	205.66	202.48	35.14	10.93	—	—	—
8 5/8	28	219.08	41.67	7.72	203.64	200.46	40.24	10.07	— 12.44	— 12.57	— 2.51
8 5/8	32	219.08	47.62	8.94	201.2	200.02 e 198.02 195.58	46.33	9.39	12.44	12.57	2.51
8 5/8	32	219.08	47.62	8.94	201.2	193.68 e	46.33	9.39	11.6	11.68	1.62
8 5/8	36	219.08	53.57	10.16	198.76	193.04	52.35	8.72	10.73	10.77	0.71
8 5/8	40	219.08	59.53	11.43	196.22	190.5	58.53	—	10.73	10.77	0.71
8 5/8	40	219.08	59.53	11.43	196.22	187.6	58.53	—	9.88	9.87	–0.20
8 5/8	44	219.08	65.48	12.7	193.68		64.64	—	8.88	8.85	–1.21
8 5/8	49	219.08	72.92	14.15	190.78		71.51	—
9 5/8	32.3	244.48	48.07	7.92	228.6	224.66	46.2	11	— 14.48	— 13.87	— 2.74
9 5/8	36	244.48	53.57	8.94	226.6	222.63	51.93	10.36	13.59	12.97	1.84
9 5/8	40	244.48	59.53	10.03	224.4	222.25 e 220.45 218.41 218.41 216.54 216.54	57.99	9.69	13.59	12.97	1.84
9 5/8	40	244.48	59.53	10.03	224.4	215.90 e	57.99	9.69	12.78	12.15	1.01
9 5/8	43.5	244.48	64.74	11.05	222.4	215.90 e 212.83 212.83	63.61	—	12.84 f	12.15	1.01
9 5/8	43.5	244.48	64.74	11.05	222.4	212.72 e	63.61	—	12.03	11.39	0.25
9 5/8	47	244.48	69.94	11.99	220.5	212.72 e 210.29 210.29 209.58 206.38 203.23 200.02	68.75	—	12.09 f	11.39	0.25
9 5/8	47	244.48	69.94	11.99	222.5		68.75	—	10.57	9.92	–1.22
9 5/8	53.5	244.48	79.62	13.84	216.8		78.72	—	10.63 f	9.92	–1.22
9 5/8	53.5	244.48	79.62	13.84	216.8		78.72	—	10.57	9.92	–1.22
9 5/8	53.5	244.48	79.62	13.84	216.8		78.72	—	10.63 f	9.92	–1.22
9 5/8	53.5	244.48	79.62	13.84	216.8		78.72	—	9.58	8.92	–2.22
9 5/8	58.4	244.48	86.91	15.11	214.25		85.47	—	9.65 f	8.92	–2.22
9 5/8	58.4	244.48	86.91	15.11	214.25		85.47	—	9.58	8.92	–2.22
9 5/8	58.4	244.48	86.91	15.11	214.25		85.47	—	9.65 f	8.92	–2.22
9 5/8	58.4	244.48	86.91	15.11	214.25		85.47	—	—	—	—
9 5/8	59.4	244.48	88.4	15.47	213.5		87.37	—	—	—	—
9 5/8	64.9	244.48	96.58	17.07	210.3		95.73	—	—	—	—
9 5/8	70.3	244.48	104.62	18.64	207.2		103.82	—	—	—	—
9 5/8	75.6	244.48	112.51	20.24	204		111.93	—
							Calculated Mass c
			Nominal Linear Mass T& C b,c	Wall Thick- ness				em, Mass Gain or Loss Due to End Finishing d
Labels a		Outside Diameter			Inside Diameter	Drift Diameter	Plain- end	kg
								Round Thread		Buttress Thread
							wpe
		D	kg/m	t	D	mm	kg/m	Short	Long	RC	SCC
		mm		mm	mm
1	2	3	4	5	6	7	8	9	10	11	12
10 3/4	32.75	273.05	48.74	7.09	258.9	254.91	46.5	13.94	—	— 15.38	— 3.03
10 3/4	40.5	273.05	60.27	8.89	255.3	251.31	57.91	11.91	—	14.21	1.86
10 3/4	45.5	273.05	67.71	10.16	252.7	250.82 e 248.77 246.23 246.33	65.87	11	—	14.21	1.86
10 3/4	45.5	273.05	67.71	10.16	252.7	244.48 e	65.87	11	—	13.05	0.7
10 3/4	51	273.05	75.9	11.43	250.2	244.48 e 243.94 243.94 241.40 241.40 238.86 238.86 234.95 231.80 228.60	73.75	10.11	—	13.05	0.7
10 3/4	51	273.05	75.9	11.43	250.2		73.75	10.16 f	—	12.25	–0.09
10 3/4	55.5	273.05	82.59	12.57	247.9		80.75	9.3	—	12.01	–0.34
10 3/4	55.5	273.05	82.59	12.57	247.9		80.75	9.35 f	—	12.25	–0.09
10 3/4	55.5	273.05	82.59	12.57	247.9		80.75	9.3	—	12.01	–0.34
10 3/4	55.5	273.05	82.59	12.57	247.9		80.75	9.35 f	—	11.07	—
10 3/4	60.7	273.05	90.33	13.84	245.4		88.47	8.42	—	10.87	—
10 3/4	60.7	273.05	90.33	13.84	245.4		88.47	8.47 f	—	9.98	—
10 3/4	65.7	273.05	97.77	15.11	242.8		96.12	7.54	—	9.74	—
10 3/4	65.7	273.05	97.77	15.11	242.8		96.12	7.60 f	—	—	—
10 3/4	73.2	273.05	108.93	17.07	238.9		107.76	—	—	—	—
10 3/4	79.2	273.05	117.86	18.64	235.8		116.95	—	—	—	—
10 3/4	85.3	273.05	126.94	20.24	232.6		126.19	—	—
11 3/4	42	298.45	62.5	8.46	281.5	279.40 e 277.50 275.44 272.39	62.56	13.27	—	—	—
11 3/4	42	298.45	62.5	8.46	281.5	269.88 e	62.56	13.27	—	— 16.04	—
11 3/4	47	298.45	69.94	9.52	279.41	269.88 e	67.83	12.42	—	14.5	—
11 3/4	54	298.45	80.36	11.05	276.4	269.65	78.32	11.23	—	13.12	—
11 3/4	60	298.45	89.29	12.42	273.6	269.65 e	87.61	10.17	—	13.12	—
11 3/4	60	298.45	89.29	12.42	273.6	269.88 e 267.36 264.92	87.61	9.77 f	—	13.12	—
11 3/4	60	298.45	89.29	12.42	273.6		87.61	10.17	—	13.12	—
11 3/4	60	298.45	89.29	12.42	273.6		87.61	9.77 f	—	—	—
11 3/4	65	298.45	96.73	13.56	271.3		95.27	—	—	—	—
11 3/4	65	298.45	96.73	13.56	271.3		95.27	—	—	—	—
11 3/4	71	298.45	105.66	14.78	268.9		103.4	—	—		—
Labels a							Calculated Mass c
			Nominal Linear Mass T& C b,c	Wall Thick- ness				em, Mass Gain or Loss Due to End Finishing d
		Outside Diameter			Inside Diameter	Drift Diameter	Plain- end	kg
								Round Thread		Buttress Thread
							wpe
		D	kg/m	t	D	mm	kg/m	Short	Long	RC	SCC
		mm		mm	mm
1	2	3	4	5	6	7	8	9	10	11	12
13 3/8	48	339.72	71.43	8.38	322.96	318.99	68.48	15.04	—	— 17.91	—
13 3/8	54.5	339.72	81.1	9.65	320.42	316.45	78.55	13.88	—	16.44	—
13 3/8	61	339.72	90.78	10.92	317.88	313.91	88.55	12.74	—	14.97	—
13 3/8	68	339.72	101.19	12.19	315.34	311.37	98.46	11.61	—	14.97	—
13 3/8	68	339.72	101.19	12.19	315.34	311.37	98.46	11.67 f	—	14.33	—
13 3/8	72	339.72	107.15	13.06	313.6	311.15 e	105.21	10.98	—	13.98	—
13 3/8	72	339.72	107.15	13.06	313.6	311.15 e 309.63 309.63	105.21	10.91 f	—	14.33	—
13 3/8	72	339.72	107.15	13.06	313.6		105.21	10.98	—	13.98	—
13 3/8	72	339.72	107.15	13.06	313.6		105.21	10.91 e	—		—
16	65	406.4	96.73	9.53	387.4	382.57	96.73	18.59	—	— 20.13	—
16	75	406.4	111.61	11.13	384.1	379.37	108.49	16.66	—	18.11	—
16	84	406.4	125.01	12.57	381.3	376.48	122.09	14.92	—	—	—
16	109	406.4	162.21	16.66	373.1	368.3	160.13	—	—		—
18 5/8	87.5	473.08	130.21	11.05	450.98	446.22	125.91	33.6	—	39.25	—
20	94	508	139.89	11.13	485.7	480.97	136.38	20.5	27.11	24.78	—
20	94	508	139.89	11.13	485.7	480.97	136.38	20.61	27.26 g 24.27 17.84	24.78	—
20	106.5	508	158.49	12.7	482.6	477.82	155.13	18.22		22	—
20	133	508	197.93	16.13	475.7	470.97	195.66	13.03		16.02	—
NOTE See also Figures D.1, D.2, and D.3.
a Labels are for information and assistance in ordering.
b Nominal linear masses, threaded and coupled (Column 4) are shown for information only.
c The densities of martensitic chromium steels (L80 Types 9Cr and 13Cr) are less than those of Carbon steels; The masses shown are therefore not accurate for martensitic chromium steels; A mass correction factor of 0.989 shall be used.
d Mass gain or loss due to end finishing; See 8.5.
e Drift diameter for most common bit size; This drift diameter shall be specified in the purchase agreement and marked on the pipe; See 8.10 for drift requirements.
f based on 758 mPa minimum yield strength or greater.
g Based on 379 mPa minimum yield strength.